What are advantages and limitations of Wi-Fi?

The Wi-Fi has its own set of advantages and limitations. 

Advantages of WiFi

- WiFi makes the deployment of local Area Networks or LANs quite cheap.  

- There are some areas where the cables cannot be installed such as in historical buildings and outdoor areas. 

- But these spaces do not have any problem in hosting a wireless LAN.  

- Wireless Network adapters are being built into almost all the laptops by the manufacturers.

- A basic level of service is provided at which different brands concerning and client network interfaces access points that are competing with each other can inter-operate. 

- The products that have been certified by Wi-Fi alliance show back word compatibility. 

- A standard device for WiFi will work at any place in the whole world unlike our phones. 

- The WPA2 or the WiFi protected access encryption is secure provided a condition that the pass phrase used is quite strong.  

- The new protocols use for WMM i.e., Quality of service increase the suitability of the Wi-Fi regarding its use in latency - sensitive applications. 

- WMM is a power saving mechanism that is used for extending the life of the battery. 

Limitations of WiFi

- Inconsistency of the operation and spectrum assignments poses a problem worldwide.  

- The range all the WiFi networks is limited. 

- A wireless access point typically uses a stock antenna having a range of 100 m outdoors and 25m indoors.

- The frequency band is a major factor for producing variations in the range.  

- The range of Wi-Fi with a 2.4 ghz frequency block is better when compared with the 5.0 ghz frequency block Wi-Fi. 

- Some wireless routers come with detachable antennas. 

- These antennas can be removed for improving the range. 

- In their place upgraded antennas can be fitted. 

- The benefit of these antennas is that they have high directional gain at the remote devices. 

- The local regulations limit the maximum amount of power that can be transmitted by a Wi-Fi. 

- The power consumption of Wi-Fi is quite higher than the other standards.  

- This is so because of the reach requirements of the wireless LAN applications.

- There are technologies available that provide a propagation range that is much shorter. 

- One such technology is Bluetooth and has very low power consumption.  

- Other technologies such as zigbee have low power consumption, a long range but provides low data rate. 

- The most commonly used wireless encryption standard is WEP or wired equivalent privacy. 

- Even this standard has been proven to be breakable even if correct configuration is used. 

- This problem was addressed by WPA or Wi-Fi protected access standard to some extent. 

- By default the wireless access points use the encryption free mode. 

- The wireless security is disabled because of which the LAN can be openly accessed. 

What are uses of Wifi?

- Routers sometimes act as a Wi-Fi access point incorporating a cable modem or a DSL modem.

- These routers are installed in buildings and homes for providing Internet access and other inter networking services to the devices that in turn are connected to a either through a cable or wireless. 

- Similarly, there are routers that are powered by battery and they consist of a Wi-Fi access point and a mobile Internet radio modem. 

- Today smartphones come with this as a built-in capability.  

- However, this feature is disabled by the carriers. 

- The carriers might charge extra money for this. 

- The standalone facilities are provided by Internet packs. 

- The places where there is no network access, wifi is used. 

- Using Wi-Fi, a direct communication link between two computers can be established.  

- There is no intermediate point.  

- This type of transmission is termed as ad hoc wifi transmission. 

- This network mode is now very popular with the multi-player game consoles. Examples are:

       > Nintendo DS

       > PlayStation portable

       > Digital cameras

       > Other consumer electronic devices.

- A citywide Wi-Fi plan has been implemented by a number of the cities around the world.  

- In India, the first city to do so was Mysore.  

- The first city in the world was Jerusalem.

- The first city in United States was Sunnyvale in California to offer city-wide wifi. 

- Another type of wifi implementation is campus-wide wifi.  

- A number of colleges in United States have set up this kind of wifi network.  

- The first university to have it was Carnegie Mellon University. 

- Using wifi, the local area Network can be deployed in very less cost.  

- There are places where it is not possible for the physical transmission medium such as cables to reach. 

- In such places wifi network is of crucial importance.  

- Also, wifi can be easily deployed in historical buildings and outdoor areas.  

- Now, because of the increasing popularity of the Wi-Fi, the manufacturers are developing Wireless Network adapters for most of the notebooks and laptops.  

- This eventually led to a fall in the price of the Wi-Fi chip set. 

- Today, the Wi-Fi chip set is economically feasible and is included in most of the devices.  

- There are many brands of client network interfaces and access-points that are competing with each other.  

- These interfaces are able to inter-operate at a basic level. 

- The Wi-Fi certification for the products is issued by wifi alliance. 

- This makes them backwards compatible with each other. 

- A standard Wi-Fi Device is supposed to work anywhere in the world. 

- The encryption standard that is considered secure is the WPA2 or wifi protected access.  

- But, this would work only if the pass phrase that is being used is strong enough. 

- The Wi-Fi has been made more suitable with the use of new protocols such as quality of service.  

- This has made wifi compatible with latency sensitive applications.  

- Nowadays, for extending battery life power saving mechanisms such as WMM are being used.  

- These are the major uses of wifi technology.

- The usage wifi has been limited because of its limited range. 

- Therefore, in order to cover up a large area several intermediate Wi-Fi access-points have to be set up. 

- The variations in the range can be produced by varying the frequency band.  

- Wifi with a small frequency block works better than wifi with a larger frequency block.

- Wifi with the larger frequency blocks are optionally used. 

- The power of wifi network can be harnessed by using high gain direction antennas instead of using detachable antennas.  

- Another factor limiting the performance of wifi transmission is the local regulations. 

- Wifi also requires high power to operate upon. 

- This is a cause of concern for the devices' batteries.

What are the parameters of QoS - Quality of Service?

With the arrival of the new technologies, applications and services in the field of networking, the competition is rising rapidly. Each of these technologies, services and applications are developed with an aim of delivering QoS (quality of service) that is either better with the legacy equipment or better than that. The network operators and the service providers follow from trusted brands. Maintenance of these brands is of critical importance to the business of these providers and operators. The biggest challenge here is to put the technology to work in such a way that all the expectations of the customers for the availability, reliability and quality are met and at the same time the flexibility for quick adaptation of the new techniques is offered to the network operators. 

What is Quality of Service?

- The quality of service is defined by its certain parameters which play a key role in the acceptance of the new technologies. 

- The organization working on several specifications of QoS is ETSI.

- The organization has been actively participating in the organization of the inter-operability events regarding the speech quality.

- The importance of the QoS parameters has been increasing ever since the increasing inter-connectivity of the networks and interaction between many service providers and network operators for delivering communication services.

- It is the quality of service that grants you the ability for the making parameters specifications based up on multiple queues in order to shoot up the performance as well as the throughput of wireless traffic as in VoIP (voice over internet), streaming media including audio and video of different types. 

- This is also done for usual IP over the access points.

- Configuration of the quality of service on these access points involves setting many parameters on the queues that are already there for various types of wireless traffic. 

- The minimum as well as the maximum wait times are also specified for the transmission. 

- This is done through the contention windows. 

- The flow of the traffic between the access point and the client station is affected by the EDCA (AP enhanced distributed channel access) parameters. 

- The traffic flow from client to the access point is controlled by the station enhanced distribution channel access parameters. 

Below we mention some parameters:

Ø  QoS preset: The options listed by the QoS are WFA defaults, optimized for voice, custom and WFA defaults.

Ø  Queue: For different types of data transmissions between AP – to – client station, different queues are defined:

- Voice (data 0): Queue with minimum delay and high priority. Data which is time sensitive such as the streaming media and the VoIP are automatically put in this queue.

- Video (data 1): Queue with minimum delay and high priority. Video data which is time sensitive is put in to this queue automatically.

- Best effort (data 2): Queue with medium delay and throughput and medium priority. This queue holds all the traditional IP data. 

- Background (data 3): Queue with high throughput and lowest priority. Data which is bulky, requires high throughput and is not time sensitive such as the FTP data is queued up here.

Ø AIFS (inter-frame space): This puts a limit on the waiting time of the data frames. The measurement of this time is taken in terms of the slots. The valid values lie in the range of 1 to 255.

Ø Minimum contention window (cwMin): This QoS parameter is supplied as input to the algorithm for determining the random back off wait time for re-transmission.

Ø cwMax

Ø maximum burst

Ø wi – fi multimedia

Ø TXOP limit

Ø Bandwidth

Ø Variation in delay

Ø Synchronization

Ø Cell error ratio

Ø Cell loss ratio

Differentiate between transparent and nontransparent fragmentation?

A number of problems are encountered because of the size of the data packets. There is no ability in the data link layer by means of which it could handle these problems and so the bridges also don’t work here. 

The Ethernet also experiences a number of problems because of the following:

Ø  Different way in which the maximum packet size is defined.

Ø  Maximum packet size that can be handled by a router.

Ø  The maximum length slot that are used for transmission

Ø  Errors due to the packet length

Ø  Standards

The data packets can be fragmented in two ways namely:

1. Transparent and
2. Non – transparent

Both these ways can be followed based on a network by network basis. We can also say that no such end – to – end agreement exists based up on which it can be decided which process is to be used.

Transparent Fragmentation: 

- This type of fragmentation is followed when a packet is split in to smaller fragments by a router.

- These fragments are sent to the next router which does just the opposite i.e., it reassembles the fragments and combine them to form original packet. 

- Here, the next network does not come to know whether any fragmentation has taken place. 

- Transparency is maintained between the small packet networks when compared to the other subsequent networks.

- For example, transparent fragmentation is used by the ATM networks by means of some special hardware. 

- There are some issues with this type of fragmentation. 

- It puts some burden on the performance of the network since all the fragments have to be transmitted through the same gateway. 

- Also, sometimes the repeated fragmentation and reassembling has to be done for small packet network in series. 

- Whenever an over-sized packet reaches a router, it is broken up in to small fragments. 

- These fragments are transported to the next exit router. 

- The fragments are assembled by this exit router which then forwards them to the next router.

- Awareness regarding this fragmentation is not maintained for the subsequent networks. 

- For a single packet fragmentation is done many times before the destination is finally reached. 

- This of course consumes a lot of time because the repeated fragmentation and assembling has to be carried out. 

- Sometimes, it also presents the reason of corrupting the packet’s integrity.

Non-Transparent Fragmentation: 

- In this type, the packet is split in to fragments by one router. 

- But the difference is that these fragments are not reassembled until the fragments reach their destination. 

- They remain split till then. 

- Since in this type of fragmentation the fragments are assembled only at the destination host, the fragments can be routed independent of each other. 

- This type of fragmentation also experiences some problems such as header has to be carried by each of the fragments till they reach their destination. 

- Numbering has to be done for all the fragments so that no problem is experienced in reconstructing the data stream.

Whichever type of fragmentation we use, one thing has to be made sure which is that later we should be able to form the original packets using the fragments. This insists on having some type of labeling for the fragments. 

Segmentation is another name for the fragmentation. A packet is injected in to the data link layer by the IP layer but it is not responsible for reliable transmission of the packets. Some maximum value on the size of the packets is imposed by each layer for their reasons. For a large packet that travels through the network for which the MTU is small, fragmentation is very much needed. 

What is fragmentation?

- The fragmentation technique is implemented in the IP (internet protocol) for breaking down the datagrams into smaller pieces. 

- This is done so that it becomes easy for the data packets to be passed through the link with a datagram size smaller than that of the original MTU or the maximum transmission unit. 

- The procedure for the IP fragmentation along with the procedures for reassembling and transmitting the datagrams is given in the RFC 791. 

- For determining the optimal MTU path, the IPv6 hosts are needed so that the packets can be sent. 

- If in case the PDU i.e., the protocol data unit received by the router is larger than the MTU of the next hop, then there are two options are available if IPv4 transport is being used:

Ø Dropping the PDU and sending an ICMP (internet control message protocol) message indicating that the condition packet is quite big.

Ø  Fragmenting the IP packet and then transmitting it over the link whose MTU is smaller. Any IPv6 packet with a size less than or equal to 1280 bytes can be delivered without having the need for using the IPv6 fragmentation.

- If a fragmented IP packet is received by the recipient host, its job is to reassemble the datagram and then send it over to the protocols at the higher layers. 

- The purpose of reassembling is expected to take place at the recipient’s host side but for some practical reasons it might be done by some intermediate router. 

- For example, the fragments might be reassembled by the NAT (network address translation) for translating the data streams. 

- Excessive re-transmission can result as a consequence of the IP fragmentation whenever packet loss might be encountered by the fragments. 

- It is required for all the reliable protocols (example, TCP) for re-transmitting the fragments in their correct order for recovering from the single fragment loss. 

Thus, typically two approaches are used by the senders for determining datagrams of what size should be transmitted over the network:

1. First approach: The sender must transmit an IP datagram of size as same as that of the first hop’s MTU.
2. Second approach: Running the path MTU discovery algorithm.

- Fragmentation does leave an impact on the network forwarding. 

- When there are multiple parallel paths for the internet router the traffic is split by the technologies such as the CEF and LAG throughout the links via some hash algorithms. 

- The major goal of this algorithm is to make sure that all the packets with the same flow are transmitted out on the same path for the minimization of the not so required packet reordering. 

- If the TCP or UDP port numbers are used by the hash algorithm, the fragmented packets might be forwarded through different paths. 

- This is so because the layer 4 information is contained only in the first fragment of the packet. 

- As a result of this, usually the initial fragment arrives after the non-initial fragments. 

- This condition is often treated as an error by most of the security devices in the hosts.  

- Therefore, they drop these packets.

- The fragmentation mechanism differs in IPv4 and IPv6. 

- In the former, the fragmentation is performed by the router. 

- On the other hand, in IPv6 fragments that are larger than MTU are dropped by the routers.

- Also, in both the cases there is a variation in the header format. 

- Since fragmentation is carried out using analogous fields, therefore the algorithm can be used again and again for the purpose of fragmentation and reassembling. 

- A best effort should be made by the IPv4 hosts for reassembling the datagram fragments. 

What are the advantages and disadvantages of datagram approach?

- Today’s packet switching networks make use of a basic transfer unit commonly known as the datagram. 

- In such packet switched networks, the order of the data packets arrival, time of arrival and delivery comes with no guarantee. 

- The first packet switching network to use the datagrams was CYCLADES. 

- Datagrams are known by different names at different levels of the OSI model. 

- For example, at layer 1 we call it Chip, at layer 2 it is called Frame or cell, data packet at layer 3 and data segment at layer 4. 

- The major characteristic of a datagram is that it is independent i.e., it does not rely on any other thing for the information required for exchange.

- The duration of a connection between any two points is not fixed such as in telephone conversations. 

- Virtual circuits are just the opposite of the datagrams. 

- Thus, a datagram can be called as a self containing entity. 

- It consists of information sufficient for routing it from the source to the destination without depending up on the exchanges made earlier. 

- Often, a comparison is drawn between the mail delivery service and the datagram service. 

- The user’s work is to just provide the address of the destination. 

- But he/she is not guaranteed the delivery of the datagram and if the datagram is successfully delivered, no confirmation is sent to the user. 

- The data gram are routed to some destination without help of a predetermined path. 

- The order in which the data has to be sent or received is given no consideration. 

- It is because of this that the datagrams belonging to a single group might travel over different routes before they reach their common destination. 

Advantages of Datagram Approach

1. Datagrams can contain the full destination address rather than using some number.
2. There is no set up phase required for the datagram circuits. This means that no resources are consumed.
3. If it happens during a transmission that one router goes down, the datagrams that will suffer will include only those routers which would have been queued up in that specific router. The other datagrams will not suffer.
4. If any fault or loss occurs on a communication line, the datagrams circuits are capable of compensating for it.
5. Datagrams play an important role in the balancing of the traffic in the subnet. This is so because halfway the router can be changed.

Disadvantages of Datagram Approach

1. Since the datagrams consist of the full destination address, they generate more overhead and thus lead to wastage of the bandwidth. This in turn makes using datagram approach quite costly.
2. A complicated procedure has to be followed for datagram circuits for determining the destination of the packet.
3. In a subnet using the datagram approach, it is very difficult to keep congestion problems at bay.
4. The any-to-any communication is one of the key disadvantages of the datagram subnets. This means that if a system can communicate with any device, any of the devices can communicate with this system. This can lead to various security issues.
5. Datagram subnets are prone to losing or re - sequencing the data packets during the transition. This puts a great burden on the end systems for monitoring, recovering, and reordering the packets as they were originally.
6. Datagram subnets have less capability of dealing with congestion control as well as flow control. This happens because the direction of the incoming traffic is not specified. In the virtual circuit subnets, the flow of the packets is directed only along the virtual circuits thus making it comparatively easy for controlling it.
7. The unpredictable nature of the flow of the traffic makes it difficult to design the datagram networks. 

Application areas of leaky bucket algorithm and token bucket algorithm

In this article we discuss about the applications of the leaky bucket algorithm and the token bucket algorithm.  

Applications of Leaky Bucket Algorithm

- The leaky bucket algorithm is implemented in different versions. 

- For example, the generic cell rate algorithm is a version of this algorithm which is often implemented in the networks using ATM (asynchronous transfer mode).  

- The algorithm is applied at the user interfaces in the usage/network parameter control in order to provide protection to the network from the problems of congestive collapse or excess traffic. 

- An algorithm equivalent to the generic cell rate algorithm might be used in shaping the transmissions made by the network interface card to a network using ATM. 

There are two major applications of the leaky bucket algorithm. 

- The first is using it as a counter only for checking whether the events or the traffics confirm to the defined limits or not.

- Whenever a packet arrives at the check point, the counter is incremented. 

- This is same as adding water to the bucket in an intermittent way. 

- In the same way, the counter is decremented as the water leaks out at a constant rate. 

- Because of this, the conformance of the packet to the burstiness and bandwidth limits is indicated by the value of this counter whenever a packet arrives. 

- Or if an event occurs, the counter checks whether it confirms to the peak and average rate limits. 

- So, when the packets arrive or an event occurs, water is added to the bucket and then leaks out. We call this version of the leaky bucket algorithm as a meter.

- Another application of the leaky bucket algorithm involves its use as queue implemented for controlling the flow of traffic. 

- This queue maintains a direct control over the flow. 

- When the packets arrive, they are put in to the queue. 

- This is same as adding water to the bucket. 

- The packets are then removed in the order they arrived at a constant rate. 

- This is same as water leaking out. 

- As a result of this, there is no jitter or burstiness in the traffic flow.

Applications of Token Bucket Algorithm

- The token bucket algorithm finds its application in the telecommunications and packet switched computer networks.

- This algorithm is implemented for checking whether the data transmissions confirm to the burstiness and bandwidth predefined limits. 

- The token bucket algorithm used in traffic policing and traffic shaping. 

- In the former, the packets that are non-conformant are discarded or assigned low priorities. 

- This is done for the management of the downstream traffic. 

- On the other hand, the packets are kept in delay unless they are conformed in traffic shaping. 

- Both of these are used in protecting the network against the burstiness of the traffic. 

- Bursty traffic gives rise to congestion problems. 

- These algorithms help in managing the bandwidth as well congestion of the network. 

- Network interfaces commonly use the traffic shaping process for preventing the discarding of the transmissions by the network’s traffic management functions. 

- This algorithm is based up on the analogy of a bucket with fixed capacity. 

- Tokens are added to this bucket at a fixed rate and represent a single packet of a fixed size. 

- When the packet has to be checked whether it confirms to the predefined limits or not, first the bucket is checked if it contains sufficient tokens. 

- If sufficient tokens are there, tokens equal to the number of bytes in the packet are removed and the packet is transmitted. 

- If sufficient tokens are not there, the packet is said to be non-conformant and the number of tokens in the bucket remain unchanged.

What is the difference between leaky bucket algorithm and token bucket algorithm?

- Telecommunications networks and the packet switched computer networks make use of the leaky bucket algorithm for checking the data transmissions. 

- This check is carried out in the form of packets. 

About Leaky Bucket Algorithm

- This algorithm is used for determining whether the data transmissions confirm to the limits that have been defined for the burstiness and bandwidth. 

- Leaky bucket counters also use the leaky bucket algorithm for detecting the peak or the average rate of the stochastic or random events and processes and if they are exceeding the predefined limits. 

We shall take analogy of a bucket for explaining this algorithm.

- Consider a bucket having a hole in its bottom through which the water it has will leak away. 

- The rate of leakage is constant if it is not empty. 

- We can intermittently add water to it that is in short bursts. 

- But if a large amount of water is added to it in one go, the water will exceed the bucket’s capacity and overflow will occur. 

- Hence, it is determined using this leaky bucket algorithm that whether or not adding water to it will make up the average rate or will exceed it. 

- Leak rate sets the average rate of adding the water and depth of the bucket decides the amount of water to be added. 

- Asynchronous transfer mode networks use the generic cell rate algorithm which is one of the versions of the leaky bucket algorithms. 

- At the user network interfaces, these algorithms are used in the usage/ network parameter control. 

- The algorithm is also used in network-network interfaces and inter-network interfaces for protecting networks from the overwhelming traffic levels through the connections in the network. 

- A network interface card can be used on a network using ATM for shaping the transmissions. 

- This network interface card might use an equivalent of the generic cell rate algorithm or this algorithm itself.

- The leaky bucket algorithm can be implemented in two different ways both of which are mentioned in the literature. 

- It appears as if there are two distinct algorithms that are together known as the leaky bucket algorithm.

About Token Bucket Algorithm

- At an interval of every 1/r seconds the token bucket algorithm adds a token to a bucket. 

- The maximum number of tokens that can be handled by a bucket are b. 

- Any token above this limit is rejected by the bucket. 

- When the bucket receives a packet from the network layer consisting of n bytes, the n numbers of tokens are taken out from the bucket and then the packet is transmitted in to the network. 

- If number of tokens available is less than n, the packet is treated as being non-conformant. 

- A bucket with a fixed capacity is associated with some virtual user and the rate at which it leaks is fixed. 

- No leakage occurs if there is nothing in the bucket. 

- Some water has to be added to the bucket in order to make the packet conform-ant. 

- No water is added to the bucket if adding this amount of water will cause the bucket to exceed its capacity. 

- Therefore, we can see that one algorithm adds something constantly to the bucket and removes also for conforming packets. 

- The other algorithm removes something constantly and adds something for confirming packets. 

- Both the algorithms are same in effectiveness and this is why the two see each the same packet as non-confirming or confirming. 

- The leaky bucket algorithm is often used as meter.