What are uses of WiMax technology?

- The WiMax technology has been used since a long time to provide assistance to the communication process.

- This area has seen major deployment of wimax technology especially in Indonesia during the calamity of tsunami in the year of 2004. 

- The WiMax technology brought in the possibilities of providing broadband access that helped a big deal in regeneration of the communication. 

- The organizations such as FEMA and FCC (federal communications commission) felt the need of wimax in their communication process. 

- The WiMax applications with high efficiency are available today.

- It is known to offer a broad base for the customers and the services had been improved by adding mobility feature to them.

- The service providers use the WiMax technology for providing various services such as mobile and Internet access, voice, video and data. 

There are other advantages of using wimax technology.  

- You get to save a lot of prospective cost and at the same time you get efficiency in services.

- It is even capable of allowing the video making, VOIP calling and data transfers at high speeds.

- The mobile community has been upgraded so much with the coming of the WiMax technology.

- However, there are three main applications offered by WiMax namely backhaul, consumer connectivity and business.

- The real augmentation has been drawn to communications through WiMax technology because of which they can benefit both from the data transmission and video apart from voice. 

- This has facilitated quick response from the applications as per the situation.  

- A temporary communication services can be deployed by a client using WiMax technology.

- It can even speed up the network according to the circumstances and events.  

- This has got us access to visitors, employees and media on a temporary basis.  

- If we are located in the range of the tower, it is quite easy for us to gain access to the equipment of the premises of for the events.

The factors that make the wimax technology so powerful are the following:

> high bandwidth

> high quality services

> security

> deployment

> full duplex consisting of DSL

> reasonable cost

For some applications, the wimax technology is used exclusively as in the following:

1. A means of connecting for the small and medium sized businesses.  - This technology has enabled these businesses to progress day by day.

- The connectivity offered by WiMax technology is good enough to attract clients.  

- It then provides them a number of services such as that of hotspots and so on.  

- Therefore, this application has gotten into spot light.

2. Backhaul

- The most important application of the WiMax technology is the range.

- This is so because using WiMax tower can be used as a means to connect with the other WiMax towers through line-of-sight communication which involves using microwave links. 

- This connectivity between two towers is called as backhaul.  

- It is capable of covering up to 3000 miles. 

- The WiMax network is even sufficient for covering remote and rural areas.

3. The nomadic broadband is another application of wimax technology which can be considered as an extended plan of wifi.

- The access points provided by WiMax technology might be less in number but they offer very high security.  

- Many companies use the WiMax base station for the development of the business.

What is a substitution cipher method?

There are two classic methods for cryptography namely transposition cipher method and the substitution cipher method. In this article we shall discuss about the latter one i.e., the substitution cipher method. 

- This method of encoding involves replacement of the units or letters of the plain text with some other units or letters. 

- The encoded text is then called as the cipher text. 

- The replacement of the units is made based up on some regular system. 

- These units might be individual letters, pairs or triplets of letters and so on. 

- On the receiver’s side, an inverse substitution is required for deciphering the text. 

- We can make a comparison between the transposition ciphers and the substitution ciphers. 

- In the former ciphers, the plain text units are rearranged unlike in substitution cipher where units are replaced.

- The order of rearrangement in the transposition ciphers is somewhat more complex than what is followed by the substitution ciphers and the units are not changed.

- On the other side, the sequence of the units remains same in the substitution cipher but they are themselves altered. 

There are various types of substitution cipher as mentioned below:

Ø  Simple substitution ciphers: 

- This involves substitution of the single letters and thus has been termed as the simple substitution. 

- The alphabet can be written out in some order so as to represent the substitution.

- This alphabet is referred to as the substitution alphabet. 

- This alphabet might be revered or shifted or scrambled in some complex manner. 

- In such cases, it is termed as the deranged alphabet or the mixed alphabet. 

- The creation of the mixed alphabets involves writing out a keyword while removing the repeating letters and then rewriting the leftovers in the same sequence. 

- For avoiding the transmission errors, the cipher text is written in block form and the spaces and the punctuation are omitted. 

- This also helps in creating disguises for the boundaries between the words.

Ø Homophonic substitution: 

- This method is followed for increasing the difficulty for the frequency analysis attacks. 

- The frequencies of the letters of the plain text are disguised by homophony. 

- Here the letters of the plain text are mapped to many symbols of the cipher text. 

- Normally the plain text symbols with highest frequencies are mapped with more equivalents when compared to their low frequency counterparts. 

- This leads to the flattening of the frequency distribution which in turn raises the difficulty of frequency analysis. 

- For the invention of larger alphabets a number of solutions are employed. 

- The simplest of these solutions is using a numeric substitution alphabet. 

- Another method uses the variations of the existing alphabet i.e., writing it upside down, or in upper case and lower case etc. 

- Nomenclature is also a variant of the homophonic substitution. 

- The other two types of homophonic ciphers namely straddling checker board and book cipher.

Ø Polyalphabetic substitution: 

- It involves the use of the multiple cipher alphabets. 

- For the facilitation of the encryption process, these alphabets are written out in a big table which is referred to as the tableau. 

- The particular poly alphabetic cipher is defined by the method with which the tableau is filled and the alphabet is chosen. 

- Some types of the polyalphabetic ciphers are:

             1. Beaufort cipher

             2. Gronsfeld cipher

             3. Running key cipher

             4. Autokey cipher

Ø  Polygraphic substitution: 

Here the letters of the plain text are substituted in terms of large groups instead of individual letter substitution.

Ø Mechanical substitution ciphers: 

Some examples of this type of substitution ciphers are enigma, rotor cipher machines etc.

Ø The one-time pad: 

This one is a special substitution cipher which has been proven that it is unbreakable mathematically.

Differentiate between upward and downward multiplexing?

The process of multiplexing is carried out at the transport layer. Several conversations are multiplexed in to one connection or physical links or virtual circuit. For example, suppose the host has only one network address available for use. Then it has to be used by all the transport connections originating at that host. For multiplexing the following two main strategies are followed:

Ø  Upward multiplexing and

Ø  Downward multiplexing

Upward Multiplexing 

- In upward multiplexing, the different transport connections are multiplexed in to one network connection. 

- These transport connections are grouped by the transport layer as per their destinations. 

- It then maps the groups with the minimum number of network connections possible.

- The upward multiplexing is quite useful where the network connections come very expensive.

Downward Multiplexing 

- It is only used when the connections with high bandwidth are required. 

- In case of the downward multiplexing, the multiple network connections are opened by the transport layer and the traffic is distributed among them. 

- But for using downward multiplexing, it is necessary that this capacity must be handled well by the subnet’s data links.

Another Technique 

- In either of the cases it is not guaranteed that the segments will be delivered in order. 

- Therefore, another technique is adopted. 

- The segments are numbered sequentially. 

- Each octet is numbered by the TCP sequentially. 

- Segments are then numbered based up on the number of the first octet present in that segment. 

- The segments might get damaged in the transition or some may even fail to arrive at the destination. 

- This failure is not acknowledged by the transmitter. 

- However, the successful receipt of the segment is does acknowledged by the receiver. 

- Sometimes, the cumulative acknowledgements might be used. 

- If the ACK triggers a time out interrupt, the re-transmission of the segment is done. 

- Also the re-transmission is done when an ACK is lost. 

- The receiver must have the ability to recognize the duplicate ACKs. 

- If such thing occurs, the receiver assumes by itself the ACK might have been lost.

- This happens when the ACK duplicate is received before the connection is closed. 

- If the duplicate is received after the closure of the connection, the situation is dealt differently. 

- In this case, the sender and receiver are allowed to know about each other’s existence. 

- They negotiate about the parameters and the transport entity resources are allocated based up on some mutual agreement. 

The connection release is of two types:

Ø Asymmetric release: 

This is the one used in the telephone systems. However it does not works well for the network that use packet switching.

Ø  Symmetric release: 

- This is certainly better than the previous one.

- Here, all the directions are released independently with respect to each other. 

- The host continues receiving data after the disconnection TPDU has been sent. 

- But the symmetric release has another problem which is related with indirection levels and fake messages. 

- There are no proper solutions for this problem in case of the unreliable communication media. 

- Note that this has nothing to do with the protocol. 

- Putting a reliable protocol over an unreliable medium can actually guarantee the delivery of the message. 

- Another thing to be noted is that it the time limit within which the message will be delivered cannot be guaranteed by any protocol. 

- Error conditions might prolong the delivery period. 

- Restarting the connections can lead to the loss of all the state info and the connection might remain as half-open. 

- Since no protocol has been designed to deal with this problem therefore one has to go forward with the risks associated with releasing the connections. 

What is meant by multiplexing?

- Multiplexing or muxing is a very important process in computer networks and the telecommunications. 

Using this process, a number of digital data streams or analog message signals are combined as one signal and then transported over the common medium. 

- Multiplexing is used wherever it is required to share a resource that is very expensive. 

- The most common example of multiplexing is of using one wire for several telephone calls. 

- The origin of the multiplexing dates back to 1870s when telegraphy was started.

- Now it is used to a great extent in the field of communications. 

- The telephone carrier multiplexing was developed by George Owen Squire in the field of telephony. 

- The communication channel over which the multiplexed signal might be transmitted might be a physical transmission medium. 

- The high level communication channel’s capacity is divided by multiplexing process in to a number of low level logical channels where for each message or data stream one channel is used. 

- Demultiplexing is the reverse process of multiplexing. 

- This is used for the extraction of the original signals on the reception side.

- A multiplexer or MUX is a device that is used for carrying out the multiplexing process and the demultiplexer or DEMUX is the device that performs demultiplexing. 

- IMUX or inverse multiplexing is another process whose aim is just the opposite of the multiplexing.

- It breaks down a single data stream in to various streams while transferring them at the same time over various communication channels.

- Later, the original stream is recreated.

Types of Multiplexing

Many different types of multiplexing technologies are available today. Each has its own significance:

Ø SDM or space-division multiplexing: 

This technique implies on using different point – to – point wires for individual communication channels. For example, an audio cable of analogue stereo, multi – pair telephone cable, switched star network, mesh network. However typically the wired SDM is not usually considered as multiplexing. In SDM a phased array antenna is formed by multiple antennas. For example MIMO (multiple – input and multiple – output), SIMO (simple – input and multiple – output), MISO (multiple – input and single – output) etc.

Ø  FDM or frequency-division multiplexing: 

This is considered to be an analog process, here the signals are sent in to different frequency ranges over a shared medium. For example, TV and radio broadcasting from satellite stations through the earth’s atmosphere. One cable is given in each house but over this cable many signals can be sent to other subscribers also. For accessing the desired signal, the users require to tune to that particular frequency. WDM or wavelength division multiplexing is a variant of FDM.

Ø TDM or time-division multiplexing: 

Unlike FDM, TDM is a digital technology but very rarely it might be used as an analog technology also. The process involves putting bytes in a sequence for each input stream one by one. this sequencing is done in such a way that the receiver can appropriately  receive them. If this is done quickly, the fact that another logical communication path was served in that circuit time won’t be detected by the receiver.

Ø  CDM or code-division multiplexing: 

In this multiplexing technique, the same frequency spectrum is shared by the several channels at the same time. Also the bandwidth of the spectrum is quite high when compared to the symbol rate or the bit rate. It is implemented in either of the two forms namely direct sequence spread spectrum and frequency hopping.

Some other types of multiplexing techniques which are less prominent are:

Polarization-division multiplexing: Used in optical and radio communications.

Orbital angular momentum multiplexing

Explain Border Gateway Protocol (BGP)?

- BGP or Border gateway protocol is the set of rules that is implemented for making the routing decisions at the core of the internet. 

- It involves the use of the IP networks table or we can say prefixes which are used for designating the reach-ability of the network to the autonomous systems. 

- This protocol falls under the category of the path vector protocol or sometimes classified as a variant of the distance vector routing protocols. 

- The metrics of the IGP or the interior gateway protocol are not used by the border gateway protocol rather paths, rule sets or polices are used for making decisions for routing. 

- This is why the border gateway protocol is often called a reach-ability protocol rather than being termed as a routing protocol. 

- The BGP has ultimately replaced the EGP or the exterior gateway protocol. 

- This is so because it allows the full decentralization of the routing process for making transition between the ARPANET model’s core and the decentralized system that consists of a NSFNET backbone and the regional networks associated with it. 

- The present version of the BGP that is being used is the version 4. 

- The earlier versions were discarded for being obsolete. 

- The major advantage is of the classless inter-domain routing and availability of a technique called the route aggregation for making reductions in the routing size. 

- The use of the BGP has made the whole routing system a decentralized system.

- BGP is used by most of the internet service providers for establishing a route between them. 

- This is done especially when the ISPs are multi-homed. 

- That’s why even though it is not used directly by the users; it is still one of the most important protocols in networking. 

- The BGP is used internally by a number of large private IP networks. 

- For example, it is used to combine many large open shortest path first or OSPF networks where these networks do not have the capability to scale to the size by themselves. 

- BGP is also used for multi-homing a network so as to provide a better redundancy. 

- This can be either to many ISPs or to a single ISP’s multi access points. 

- Neighbors of the border gateway protocol are known as the peers. 

- They are created by manually configuring the two routers so as to establish a TCP session on the port. 

- Messages called the 19 byte keep alive messages are sent to the port periodically by the BGP speaker for maintaining the connection. 

- Among the various routing protocols, the most unique is BGP since it relies up on TCP for transporting. 

- When the protocol is implemented in the autonomous system among two peers, it is called IBGP or the internal border gateway protocol. 

- The protocol is termed as the EBGP or the external border gateway protocol when it runs between many autonomous systems.

- Border edge routers are the routers that are implemented on the boundary for exchanging information between various autonomous systems.

- BGP speakers have the capability for negotiating with the session’s option capabilities such as the multi-protocol extensions and a number of recovery modes. 

- The NLRI (network layer reach-ability information) can be prefixed by the BGP speaker if at the time of the creation itself, the multi-protocol extensions are negotiated. 

- The NLRI is advertised along with some address family prefix. 

The family consists of the following:

Ø  IPv4

Ø  IPv6

Ø  Multicast BGP

Ø  IPv4/ IPv6 virtual private networks

- These days the border gateway protocol is being commonly employed as the generalized signaling protocol whose purpose is to carry information via the routes that might not form the global internet’s part. 

What is Portability Testing?

- Portability Testing is the testing of a software/component/application to determine the ease with which it can be moved from one machine platform to another. 

- In other words, it’s a process to verify the extent to which that software implementation will be processed the same way by different processors as the one it was developed on.  

- It can also be understood as amount of work done or efforts made in order to move software from one environment to another without making any changes or modifications to the source code but in real world this is seldom possible.

- For example, moving a computer application from Windows XP environment to Windows 7 environment, thereby measuring the efforts and time required to make the move and hence determining whether it is re usable with ease or not.

- Portability testing is also considered to be one of the sub parts of System testing as this covers the complete testing of software and also it’s re-usability over different computer environments that include different Operating systems, web browsers.

What needs to be done before Portability testing is performed (pre requisites/pre conditions)? 

1.   Keep in mind portability requirements before designing and coding of software.

2.   Unit and Integration Testing must have been performed.

3.   Test environment has been set up.

Objectives of Portability Testing

1. To validate the system partially i.e. to determine if the system under consideration fulfills the portability requirements and can be ported to environments with different :-

a). RAM and disk space

b). Processor and Processor speed

c). Screen resolution

d). Operating system and its version in use.

e). Browser and its version in use.

To ensure that the look and feel of the web pages is similar and functional in the various browser types and their versions.

2.   To identify the causes of failures regarding the portability requirements, this in turn helps in identifying the flaws that were not found during unit and integration testing.

3.   The failures must be reported to the development teams so that the associated flaws can be fixed.

4.   To determine the potential or extent to which the software is ready for launch.

5.   Help in providing project status metrics (e.g., percentage of use case paths that were successfully tested).

6.   To provide input to the defect trend analysis effort.

What is the concept of flow control?

- Flow control is an important concept in the field of data communications. 

- This process involves management of the data transmission rate between two communicating nodes. 

- Flow control is important to avoid a slow receiver from being outrun by a fast sender. 

- Using flow control, a mechanism is designed for the receiver using which it can control its speed of transmission.

- This prevents the receiving node from getting overwhelmed with traffic from the node that is transmitting.

- Do not confuse yourself with congestion control and flow control. Both are different concepts. 

- Congestion control comes in to play when in actual there is a problem of network congestion for controlling the data flow. 

On the other hand the mechanism of flow control can be classified in the following two ways:

1. The feedback is sent to the sending node by the receiving node.
2. The feedback is not sent to the sending node by the receiving node.

- The sending computer might tend to send the data at a faster rate than what can be received and processed by the other computer. 

- This is why we require flow control. 

- This situation arises when the traffic load is too much up on the receiving computer when compared to the computer that is sending the data. 

- It can also arise when the processing power of the receiving computer is slower than the processing power of the one that is sending the data.

Stop and Wait Flow Control Technique 

- This is the simplest type of the flow control technique. 

- Here, when the receiver is ready to start receiving data from the sender, the message is broken down in to a number of frames. 

- The sending system then waits for a specific time to get an acknowledgement or ACK from the receiver after sending each frame. 

- The purpose of the acknowledgement signal is to make sure that the frame has been received properly. 

- If during the transmission a packet or frame gets lost, then it has to be re-transmitted. 

- We call this process as the automatic repeat request or ARQ. 

- This technique has a problem which is that it is capable of transmitting only one frame in one go. 

- This makes the transmission channel very inefficient. 

- Therefore, until and unless the sender gets an acknowledgement it will not proceed further for transmitting another packet. 

- Both the transmission channel and the sender are left un-utilized during this period. 

- Simplicity of this method is its biggest advantage. 

- Disadvantage is the inefficiency resulting because of this simplicity. 

- Waiting state of the sender creates inefficiency. 

- This happens usually when the transmission delay is shorter than the propagation delay. 

- Sending longer transmissions is another cause for inefficiencies. 

- Also, it increases the chance for the errors to creep in this protocol. 

- In short messages, it is quite easy to detect the errors early. 

- By breaking down one big message in to various separate smaller frames, the inefficiency increases. 

- This is so because these pieces altogether take a long to be transmitted.

Sliding window Flow Control Technique 

- This is another method of flow control where permission is given to the sender by the receiver for continuously transmitting data until a window is filled up. 

- Once the window is full, sender stops transmission until a larger window is advertised. 

- This method can be utilized in a better way if the size of the buffer is kept limited. 

- During the transmission, space for say n frames is allocated to the buffer. 

- This means n frames can be accepted by the receiver without having to wait for ACK. 

- After n frames an ACK is sent consisting of the sequence number of the next frame that has to be sent. 

What is meant by multi-destination routing?

- So many routing algorithms have been devised to aid in routing under different conditions.
- Effective routing algorithms have been developed that are capable of routing the messages from one source node to a number of receiving nodes i.e., the multiple destination nodes.
- These algorithms are termed as the multi – destination routing algorithms and the process is therefore called as the multi – destination routing.
- This type of routing has been developed for the minimization of the cost of the network i.e., NC (network cost).
- Network cost can be defined as the sum of all the links’ weights that consist of the routing path.
- There are many heuristic algorithms available for determining the NC min path.
- This problem falls under the category of the NP – complete problems.
- Heuristics are available for the traveling salesman problem and MST (minimum spanning tree) variations.
- Global information is used by both of them.
- Another set of such heuristics is available that uses only shortest paths for reaching the destinations.
- The best worst case performance is exhibited by the MST algorithm.
- However, one study revealed that effectiveness of the simpler heuristics is higher.
- The network cost (NC) is often compared with the destination cost (DC).
- Destination cost is the sum of the cost of all the shortest paths that lead to the destination.
- A scheme of algorithms has been developed for trading off between these two costs i.e., the NC and DC.  
- The sender of the transmitted data cannot be taken as a single node in a network where the cooperative communication is supported.
- This asks for the re-investigation of the traditional link concept.
- Any routing scheme thus depending up on this link concept needs to be reconsidered.
- Also, the potential performance gain resulting because of the cooperative communication needs to be exploited.

- Routing often gets complicated for some networks where the selection of the paths is no longer the job of a single entity.
- Rather, a number of entities are involved in the selection of the paths.
- Multiple entities can even select specific parts of a path.
- If these selected paths are chosen by the entities for their own objectives optimization then it can lead to inefficiency or serious complications in the network since they may or may not conflict with the other entities’ objectives.
- This would become clear from the following example, consider traffic moving in a system of roads.
- Now here each driver selects a path that would minimize only his/her traveling time.
- In this kind of routing, there are longer equilibrium routes (i.e., longer than the optimal.) for almost all other drivers.
- This is often termed as the Braess paradox.
- Another example is of the routing the AGVs (automated guided vehicles) by a model on some terminal.
- For prevention of the simultaneous usage of the infrastructure’s same part reservations are made. - This is called as the context – aware routing.
- The internet is divided in to a number of divisions which are nothing but Ass i.e., the autonomous system like ISPs.
- All these systems have control over the routes that lie in their own network at various different levels.

Following steps are involved in multi – destination routing:
1. The BGP protocol is used for selecting the AS – level paths.
2. A sequence of autonomous systems is produced by the BGP protocol via which the packet flow will take place.
3. The neighboring Ass offer multiple paths for each of the AS from which it can choose. Paths are selected based up on the relationships between the neighboring systems.
4. Each selected path refers to multiple corresponding router level paths.