What is meant by Quality of Service provided by network layer?

- The QoS or the quality of service is such a parameter that refers to a number of aspects of computer networks, telephony etc. 

- This parameter allows transportation of traffic as per some specific requirements. 

- Technology has advanced so much now computer networks can also be doubled up as the telephone networks for doing audio conversations. 

- The technology even supports the applications which have strict service demands. 

- The ITU defines the quality of service in telephony. 

It covers all the requirements concerning all the connection’s aspects such as the following:

Ø  Service response time

Ø  Loss

Ø  Signal – to – noise ratio

Ø  Cross – talk

Ø  Echo

Ø  Interrupts

Ø  Frequency response

Ø  Loudness levels etc.  

- The GoS (grade of service) requirement is one subset of the QoS and consists of those aspects of the connection that relate to its coverage as well as capacity. 

- For example, outage probability, maximum blocking probability and so on. 

- In the case of the packet switched telecommunication networks and computer networking, the resource reservation mechanisms come under the concept of traffic engineering. 

- QoS can be defined as the ability by virtue of which the different applications, data flows and users can be provided with different priorities. 

- It is important to have QoS guarantees if the capacity of the network is quite insufficient. 

- For example, voice over IP, IP-TV and so on. 

- All these services are sensitive to delays, have fixed bit rates and have limited capacities.

- The protocol or network supporting the QoS might agree up on some traffic contract with the network node’s reserve capacity and the software. 

- However, the quality of service is not supported by the best effort services. 

-Providing high quality communication over such networks provides a alternative to the QoS control mechanisms that are complex. 

- This happens when the capacity is over-provisioned so much that it becomes sufficient for the peak traffic load that has been expected. 

- Now since the network congestion problems have been eliminated, the QoS mechanisms are also not required. 

- It might be sometimes be taken as the level of the service’s quality i.e., the GoS. 

- For example, low bit error probability, low latency, and high bit rate and so on. 

- QoS can also be defined as a metric that reflects up on the experienced quality of the service.

- It is the cumulative effect that can be accepted. 

Certain types of the network traffic require a defined QoS such as the following:

Ø  Streaming media such as IPTV (internet protocol television), audio over Ethernet, audio over IP etc.

Ø  Voice over IP

Ø  Video conferencing

Ø  Telepresence

Ø  iSCSI, FCoE tec. Storage applications

Ø  safety critical applications

Ø  circuit emulation service

Ø  network operations support systems

Ø  industrial control systems

Ø  online games

- All the above mentioned services are examples of the inelastic services and a certain level of latency and bandwidth is required for them to operate properly. - On the other hand, the opposite kind of services such as the elastic services can work with any level of bandwidth and latency. 

- An example of these type of services is the bulk file transfer application based up on TCP.

- A number of factors affect the quality of service in the packet switched networks. 

- These factors can be broadly classified in to two categories namely technical and the human factors. 

The following factors are counted as the human factors:

Ø  reliability

Ø  scalability

Ø  effectiveness

Ø  maintainability

Ø  grade of service and so on.

- ATM (asynchronous transfer mode) or GSM like voice transmissions in the circuit switched networks have QoS in their core protocol. 

What are the differences between inter-network routing and intra-network routing?

- The individual networks when combined together form the inter-network. 

- Intermediate inter networking devices are used for making connections between them. 

- All these networking elements combine to work as single large unit. 

- The creation of the internetworking has been made possible because of the packet switching technology. 

- The router is the most common and important device used for performing inter-network routing and intranetwork routing.

- Routing across various networks in the inter network is termed as internetwork routing and routing within the same network is termed intranetwork routing. 

In this article we discuss about the differences between internetwork routing and intranetwork routing. 

- Just like inter-network, intranetwork also uses IP (internet protocol) technology for computing services and sharing information. 

- But what makes it different from internetworking is that it is limited to some organization whereas internetwork extends beyond all i.e., it is not limited.

- Or we can put it in other words: Internetwork is spread across organizations and Intranetwork lies within an organization. 

- In some cases, the term intranetwork might mean only the internal website of the organization, but in other cases it might be a larger part of the IT infrastructure of the organization. 

- Sometimes, it may span over a number of LANs (local area networks). 

- The intranetwork is driven by the goal of minimizing the time, effort and cost of the individual’s desktop in order to make it more competitive, cost efficient, timely as well as productive.

- An intranetwork is capable of hosting multiple websites that are private to organizations and may even constitute an important part of the collaboration and communication between the members of the organization. 

- Intranetwork also makes use of various well known protocols such as the FTP, SMTP and HTTP. 

- The intranets are often incorporated with the technologies for lending a modern interface to the systems that host the corporate data. 

- These systems are known as the legacy systems. 

- We can see intranetwork to be a private analog of the internetwork. 

- It means the internetwork has been simply extended to an organization for its private use. 

- Extranetworks are a modified version of the intranetworks.

- Here, the website might be accessed by the non-members i.e., the suppliers, customers or some other approved third parties and so on. 

- Intranetworks are well equipped with a special protocol called the AAA protocol. 

- The 3 As stand for authentication, authorization and accounting. 

- There are a number of organizations who are concerned about the security of their intranetworks. 

- They have deployed a firewall and a network gateway for controlling the access to their services. 

- The intermediate systems when connect together form the internetwork whereas they may bound together a part of the internetwork which might be an intranetwork. 

- The intranetwork routing involves routing between two routers which lie in the same network whereas in internetwork routing, routing is done between routers which reside across different networks. 

- Intranetwork routing is quite easy when compared to the internetwork routing. 

- Protocols used in both the types of routing are different.

- Interior gateway protocol is responsible for routing in the intranetworks whereas the exterior gateway protocol takes the responsibility of routing across the internetwork. 

- Most common example of interior gateway protocol is the OSPF or the open shortest path first protocol. 

- And most common example of exterior gateway protocol is the border gateway protocol or BGP. 

- Also, the routing graphs for both the types are different. 

- In the intranetwork’s graph, all the routers are simply linked to one another in the same network. 

- There is less mess.

- On the other hand, the inter network’s graph is quite tedious. 

- This is so because routers of different networks have to be inter-linked with one another. 

What is inter-network routing?

In this article we shall discuss about inter-network routing. Before moving to that there are certain terms with which you should be familiar:

Ø  End systems: The ISO (the international standards of organization) defines the end systems as the network elements that do not have the ability of forwarding the packets across the networks. Sometimes the term host is used to refer to the end systems.

Ø  Intermediate systems: These are the network elements that have the ability of forwarding the packets across the network. Most common examples are routers, switches, bridges and so on.

Ø  Network: It can be defined as a part of the inter-network infrastructure encompassing various elements including hubs, repeaters, bridges and so on. The networks are bounded by the intermediate systems.

Ø Router: This is one of the intermediate systems that is used for connecting various networks with each other. It might support one protocol (router) or many protocols (multi-protocol router). Its hardware part is optimized especially for performing routing. The software part is responsible for carrying out the routing and takes care of the routing tables.

Apart from these devices, there are 3 types of addresses involved in inter-network routing:

Ø  The inter-network address: The host address and the network address are combined together to form this address. This is used for unique identification of a host over the inter-network.

Ø The host address or host ID: This ID might be assigned by the administrator or might be simply the physical address of the host. It is used for the unique identification of the host on its network.

Ø  The network address or network ID: This is address of a network for identifying it in an inter-network.

All the data packets consist of a network layer header. This network layer header consists of the following when the packet is transmitted from one host to another:

ØThe address of the source inter-network: This address combines the address of the source host and the source network.

ØThe address of the destination inter-network: This address combines the address of the destination host and the destination network.

ØThe hop count: This usually begins at zero and is numerically incremented when the packet crosses a router. Or in the opposite case it might be assigned some maximum value which might be decremented on reaching a router. The purpose of using the hop count is to make sure that the packet does not keeps on circulating endlessly in the network.

- For inter-network routing, two things have to be known.

- Firstly, how do you reach other routers which lie in the same network and secondly, how do you reach other routers which lie in other networks? 

- The answer to the first question is easy as it is the common routing problem among two hosts residing over the same network. 

- This routing is handled by the interior gateway protocol and it is different for different networks since only local routing info is required. 

- In this case, the commonly used protocol is the open shortest path first or OSPF protocol. 

- The routing between two different networks is performed using the exterior gateway protocol. 

- This is actually the problem of inter-network routing. 

- Here, the commonly used protocol is the BGP or the border gateway protocol. 

- The graph for inter-network routing is quite different from the one that is used in the network routing. 

- This is so because the routers which lie in the same network can be thought of as being directly connected to one another for routing across inter-network. - All the networks in an inter-network function as though they are one large unit. 

Explain the concept of inter-networking?

- The practice in which one computer network is connected with the other networks is called inter-networking. 

- The networks are connected with the help of gateways. 

- These gateways are used since they offer a common method for routing the data packets across the networks.

- The resulting system in which a number of networks are connected is called the inter-network or more commonly as the internet. 

- The terms “inter” and “networking” combine together to form the term “internet working”.  

- Internet is the best and the most popular example of the inter networking. 

- Internet has formed as a result of many networks connected with the help of numerous technologies. 

- Many types of hardware technologies underlie the internet. 

- The internet protocol suite (IP suite) is the inter networking protocol standard responsible for unifying the diverse networks. 

- This protocol is more commonly known as the TCP/ IP. 

- Two computer local area networks (LANs) connected to one another by means of a router form the smallest internet but not the inter network. 

- Inter networking is not formed by simply connecting two LANs together via a hub or a switch. 

- This is called expansion of the original local area network. 

- Inter networking was started as a means for connecting the disparate networking technologies. 

- Eventually, it gained widespread popularity because of the development needs of connecting many local area networks together through some kind of WAN (wide area network). 

- “Catenet” was the original term that was used for the inter network. 

- Inter network includes many types of other networks such as the PAN or personal area network. 

- Gateways were the network elements that were originally used for connecting various networks in predecessor of the internet called the ARPANET. 

- Today, these connecting devices are more commonly known as the internet routers. 

- There is a type of interconnection between the various networks at the link layer of the networking model. 

- This layer is particularly known as the hardware centric layer and it lies below the TCP/ IP logical interfaces level. 

Two devices are mainly used in establishing this interconnection:

Ø  Network switches and

Ø  Network bridges

- Even now this cannot be called as inter networking rather, the system is just a single and large sub-network. 

- Further, for traversing these devices no inter networking protocol is required. 

- However, it is possible to convert a single network in to an inter network. 

- This can be done by making various segments out of the network and also making logical divisions of the segment traffic using the routers. 

- The internet protocol suite has been particularly designed for providing a packet service. 

- This packet service offered by the IPS is quite unreliable. 

- The elements that maintain a network state and are intermediate in the network are avoided by the architecture. 

- The focus of the architecture is more on the end points of the active communication session.

- For a reliable transfer of the data, a proper transport layer protocol must be used by the applications. 

- One such protocol is the TCP (transmission control protocol) and it is capable of providing a reliable stream for communication. 

- Sometimes a simpler protocol such as the UDP (user datagram protocol) might be used by the applications. 

- The applications using this protocol carry out only those tasks for which reliable data delivery is not required or for which realtime is required. 

Examples of such tasks include voice chat or watching a video online etc. Inter networking uses two architectural models namely:

1. OSI or the open system interconnection model: This model comes with 7 layer architecture that covers the hardware and the software interface.
2. TCP/ IP model: The architecture of this model is somewhat loosely defined when compared with the OSI model. 

What is the idea behind link state routing?

There are two main classes of the routing protocols out of which one is the link state routing protocol on which we shall focus in this article. The other class of the routing protocols is the distance vector routing protocols.

In computer communications, the link state routing protocol is applied in the packet switching networks. 

We can give two main examples of the link state routing protocol namely:

1. IS – IS i.e., intermediate system to intermediate system and
2. OSPF i.e., the open shortest path first

Almost every switching node is capable of performing the link – state routing in the network. Switching nodes can be defined as the nodes that can forward the packets. We call these nodes as routers in the internet.

Idea behind the Link State Routing

 

- A map is constructed by every node concerning its connectivity with the network. 

- This map is actually in a graph’s form. 

- This graph shows all the connections that exist between the various nodes in the graph. 

- The next “best logical path” is then calculated independently by each node to every destination in the network based up on its possibility. 

- The routing table of the node will then be formed by this collection of the best paths.

- This is in total contrast with the second class of the routing protocols.

- In the distance vector routing protocols, the routing table of a node is also shared by its neighbors whereas in the link state routing protocol, only the connectivity related information is passed between the nodes. 

- The simplest configuration of the link state routing protocols is the one that has no area. 

- This implies that each node possesses a map of the whole network. 

- The first main stage involves providing map of the network to each node. 

For doing the following, subsidiary steps are followed:

1. Determination of the neighboring nodes: Each node determines to which all neighboring nodes it is connected to. Also, it needs to know whether over the links through which it is connected are fully working or not. A reach-ability protocol is used for accomplishing this task. This protocol is run regularly but in separation from the neighboring nodes.
2. Distribution of the map information: The link state advertisement is the short message that is made by the node in case of some modification in the connectivity periodically.

- The above obtained set of such link state advertisements is used for the creation of the map of the entire network. 

- The second stage involves production of the routing tables through the map inspection. 

This again involves a number of steps:

1. Calculation of the shortest paths: Shortest path from one node to other nodes is determined by running a shortest path routing algorithm over the entire map. The commonly used algorithm is the Dijkstra’s algorithm.
2. Filling the routing table: The table is filled with best shortest paths obtained in the above step for every two nodes.  
3. Optimizations: We gave a glance of the simple form of this algorithm but in practical applications this form is used along with a number of optimizations. Whenever a change is detected in the network connectivity, the shortest path tree has to be immediately recomputed and then the routing table must be recreated. A method was discovered by the BBN technologies for recomputing only the affected part of the tree.

- Routing loops can be formed if working of the nodes using the exactly same map is not proper. 

- For adhoc networks such as the mobile networks, the optimized form of the protocol i.e., the optimized link state routing protocol is used. 

What are data gram sub-nets?

- A data gram is defined as the basic transfer unit used in the networks that operate with the help of packet switching network. 

- In such networks, the time of the arrival and delivery is not guaranteed. 

- Also, the network services do not guarantee that whether it will be an ordered delivery or not. 

- The first project to use the data grams was the CYCLADES which was again a packet switching network. 

- The hosts in this network were responsible for making a reliable delivery rather than relying on the network for doing so. 

- This they did using the data grams that were themselves so unreliable and by associating the mechanisms of the end to end protocols. 

- According to Louis Pouzin, there are two sources from which came the inspiration for the data grams namely the Donal Davie’s studies and simplicity of the things. 

- The concept of the data gram sub-net was eventually adopted for the formulation of the protocols such as apple talk, Xerox network systems and of course the internet protocol.

- Data grams are used at the first 4 layers of the OSI model. 

- Each layer has its own name for the data grams as we mention below:

1. Layer 1: chip (CDMA)
2. Layer 2: frames (IEEE 802.3 and IEEE 802.11), cell (ATM)
3. Layer 3: data packet
4. Layer 4: data segment

- A data gram is a data packet that is self-reliant. 

- This means it does not rely on any of the exchanges made earlier since the fixed connection between the two points of communication has no connection such as in a majority of the telephonic conversations. 

- Virtual circuits and data gram sub-nets are two equally opposite things. 

Data gram is defined as an independent and self-contained data entity by the RFC 1594 that carries sufficient information required for routing from one source to another without relying on the transporting network and the earlier exchanges between the two same hosts.

- The services offered by the data gram sub nets can be compared to the mail delivery services. 

- This is so because the user needs to mention only the destination address.

- However, this service does not give any guarantee of whether the data gram will be delivered or not and also does not provide any confirmation upon successful delivery of the packet. 

- These are of course two major disadvantages of the data gram sub nets. 

- In data gram sub nets, the data grams or the data packets are routed along a route that is created at the same time. 

- In data gram sub nets the routes are not predetermined. 

- This again has its disadvantages. 

- Also, the order in which the data grams have to be sent or received is not considered. 

- In some cases, a number of data grams having same destination might travel along various different routes.

- There are two components of every data gram namely the header and the data payload.

- The former consists of all the information that is enough for the routing purpose from source to the destination without being dependent on the exchanges that were made before between the network and the equipment. 

- The source as well the destination address might be included in the header as a kind of a field. 

- The data that is to be transmitted is stored in the latter part of the data gram. 

- In some cases the data payloads might be nested in to the tagged header. 

- This process is commonly known as the encapsulation. 

- There are various types of data grams for which various standards are defined by the internet protocol or IP.