What are advantages and limitations of Wi-Fi?

The Wi-Fi has its own set of advantages and limitations. 

Advantages of WiFi

- WiFi makes the deployment of local Area Networks or LANs quite cheap.  

- There are some areas where the cables cannot be installed such as in historical buildings and outdoor areas. 

- But these spaces do not have any problem in hosting a wireless LAN.  

- Wireless Network adapters are being built into almost all the laptops by the manufacturers.

- A basic level of service is provided at which different brands concerning and client network interfaces access points that are competing with each other can inter-operate. 

- The products that have been certified by Wi-Fi alliance show back word compatibility. 

- A standard device for WiFi will work at any place in the whole world unlike our phones. 

- The WPA2 or the WiFi protected access encryption is secure provided a condition that the pass phrase used is quite strong.  

- The new protocols use for WMM i.e., Quality of service increase the suitability of the Wi-Fi regarding its use in latency - sensitive applications. 

- WMM is a power saving mechanism that is used for extending the life of the battery. 

Limitations of WiFi

- Inconsistency of the operation and spectrum assignments poses a problem worldwide.  

- The range all the WiFi networks is limited. 

- A wireless access point typically uses a stock antenna having a range of 100 m outdoors and 25m indoors.

- The frequency band is a major factor for producing variations in the range.  

- The range of Wi-Fi with a 2.4 ghz frequency block is better when compared with the 5.0 ghz frequency block Wi-Fi. 

- Some wireless routers come with detachable antennas. 

- These antennas can be removed for improving the range. 

- In their place upgraded antennas can be fitted. 

- The benefit of these antennas is that they have high directional gain at the remote devices. 

- The local regulations limit the maximum amount of power that can be transmitted by a Wi-Fi. 

- The power consumption of Wi-Fi is quite higher than the other standards.  

- This is so because of the reach requirements of the wireless LAN applications.

- There are technologies available that provide a propagation range that is much shorter. 

- One such technology is Bluetooth and has very low power consumption.  

- Other technologies such as zigbee have low power consumption, a long range but provides low data rate. 

- The most commonly used wireless encryption standard is WEP or wired equivalent privacy. 

- Even this standard has been proven to be breakable even if correct configuration is used. 

- This problem was addressed by WPA or Wi-Fi protected access standard to some extent. 

- By default the wireless access points use the encryption free mode. 

- The wireless security is disabled because of which the LAN can be openly accessed. 

What are uses of Wifi?

- Routers sometimes act as a Wi-Fi access point incorporating a cable modem or a DSL modem.

- These routers are installed in buildings and homes for providing Internet access and other inter networking services to the devices that in turn are connected to a either through a cable or wireless. 

- Similarly, there are routers that are powered by battery and they consist of a Wi-Fi access point and a mobile Internet radio modem. 

- Today smartphones come with this as a built-in capability.  

- However, this feature is disabled by the carriers. 

- The carriers might charge extra money for this. 

- The standalone facilities are provided by Internet packs. 

- The places where there is no network access, wifi is used. 

- Using Wi-Fi, a direct communication link between two computers can be established.  

- There is no intermediate point.  

- This type of transmission is termed as ad hoc wifi transmission. 

- This network mode is now very popular with the multi-player game consoles. Examples are:

       > Nintendo DS

       > PlayStation portable

       > Digital cameras

       > Other consumer electronic devices.

- A citywide Wi-Fi plan has been implemented by a number of the cities around the world.  

- In India, the first city to do so was Mysore.  

- The first city in the world was Jerusalem.

- The first city in United States was Sunnyvale in California to offer city-wide wifi. 

- Another type of wifi implementation is campus-wide wifi.  

- A number of colleges in United States have set up this kind of wifi network.  

- The first university to have it was Carnegie Mellon University. 

- Using wifi, the local area Network can be deployed in very less cost.  

- There are places where it is not possible for the physical transmission medium such as cables to reach. 

- In such places wifi network is of crucial importance.  

- Also, wifi can be easily deployed in historical buildings and outdoor areas.  

- Now, because of the increasing popularity of the Wi-Fi, the manufacturers are developing Wireless Network adapters for most of the notebooks and laptops.  

- This eventually led to a fall in the price of the Wi-Fi chip set. 

- Today, the Wi-Fi chip set is economically feasible and is included in most of the devices.  

- There are many brands of client network interfaces and access-points that are competing with each other.  

- These interfaces are able to inter-operate at a basic level. 

- The Wi-Fi certification for the products is issued by wifi alliance. 

- This makes them backwards compatible with each other. 

- A standard Wi-Fi Device is supposed to work anywhere in the world. 

- The encryption standard that is considered secure is the WPA2 or wifi protected access.  

- But, this would work only if the pass phrase that is being used is strong enough. 

- The Wi-Fi has been made more suitable with the use of new protocols such as quality of service.  

- This has made wifi compatible with latency sensitive applications.  

- Nowadays, for extending battery life power saving mechanisms such as WMM are being used.  

- These are the major uses of wifi technology.

- The usage wifi has been limited because of its limited range. 

- Therefore, in order to cover up a large area several intermediate Wi-Fi access-points have to be set up. 

- The variations in the range can be produced by varying the frequency band.  

- Wifi with a small frequency block works better than wifi with a larger frequency block.

- Wifi with the larger frequency blocks are optionally used. 

- The power of wifi network can be harnessed by using high gain direction antennas instead of using detachable antennas.  

- Another factor limiting the performance of wifi transmission is the local regulations. 

- Wifi also requires high power to operate upon. 

- This is a cause of concern for the devices' batteries.

What is a substitution cipher method?

There are two classic methods for cryptography namely transposition cipher method and the substitution cipher method. In this article we shall discuss about the latter one i.e., the substitution cipher method. 

- This method of encoding involves replacement of the units or letters of the plain text with some other units or letters. 

- The encoded text is then called as the cipher text. 

- The replacement of the units is made based up on some regular system. 

- These units might be individual letters, pairs or triplets of letters and so on. 

- On the receiver’s side, an inverse substitution is required for deciphering the text. 

- We can make a comparison between the transposition ciphers and the substitution ciphers. 

- In the former ciphers, the plain text units are rearranged unlike in substitution cipher where units are replaced.

- The order of rearrangement in the transposition ciphers is somewhat more complex than what is followed by the substitution ciphers and the units are not changed.

- On the other side, the sequence of the units remains same in the substitution cipher but they are themselves altered. 

There are various types of substitution cipher as mentioned below:

Ø  Simple substitution ciphers: 

- This involves substitution of the single letters and thus has been termed as the simple substitution. 

- The alphabet can be written out in some order so as to represent the substitution.

- This alphabet is referred to as the substitution alphabet. 

- This alphabet might be revered or shifted or scrambled in some complex manner. 

- In such cases, it is termed as the deranged alphabet or the mixed alphabet. 

- The creation of the mixed alphabets involves writing out a keyword while removing the repeating letters and then rewriting the leftovers in the same sequence. 

- For avoiding the transmission errors, the cipher text is written in block form and the spaces and the punctuation are omitted. 

- This also helps in creating disguises for the boundaries between the words.

Ø Homophonic substitution: 

- This method is followed for increasing the difficulty for the frequency analysis attacks. 

- The frequencies of the letters of the plain text are disguised by homophony. 

- Here the letters of the plain text are mapped to many symbols of the cipher text. 

- Normally the plain text symbols with highest frequencies are mapped with more equivalents when compared to their low frequency counterparts. 

- This leads to the flattening of the frequency distribution which in turn raises the difficulty of frequency analysis. 

- For the invention of larger alphabets a number of solutions are employed. 

- The simplest of these solutions is using a numeric substitution alphabet. 

- Another method uses the variations of the existing alphabet i.e., writing it upside down, or in upper case and lower case etc. 

- Nomenclature is also a variant of the homophonic substitution. 

- The other two types of homophonic ciphers namely straddling checker board and book cipher.

Ø Polyalphabetic substitution: 

- It involves the use of the multiple cipher alphabets. 

- For the facilitation of the encryption process, these alphabets are written out in a big table which is referred to as the tableau. 

- The particular poly alphabetic cipher is defined by the method with which the tableau is filled and the alphabet is chosen. 

- Some types of the polyalphabetic ciphers are:

             1. Beaufort cipher

             2. Gronsfeld cipher

             3. Running key cipher

             4. Autokey cipher

Ø  Polygraphic substitution: 

Here the letters of the plain text are substituted in terms of large groups instead of individual letter substitution.

Ø Mechanical substitution ciphers: 

Some examples of this type of substitution ciphers are enigma, rotor cipher machines etc.

Ø The one-time pad: 

This one is a special substitution cipher which has been proven that it is unbreakable mathematically.

What is meant by multiplexing?

- Multiplexing or muxing is a very important process in computer networks and the telecommunications. 

Using this process, a number of digital data streams or analog message signals are combined as one signal and then transported over the common medium. 

- Multiplexing is used wherever it is required to share a resource that is very expensive. 

- The most common example of multiplexing is of using one wire for several telephone calls. 

- The origin of the multiplexing dates back to 1870s when telegraphy was started.

- Now it is used to a great extent in the field of communications. 

- The telephone carrier multiplexing was developed by George Owen Squire in the field of telephony. 

- The communication channel over which the multiplexed signal might be transmitted might be a physical transmission medium. 

- The high level communication channel’s capacity is divided by multiplexing process in to a number of low level logical channels where for each message or data stream one channel is used. 

- Demultiplexing is the reverse process of multiplexing. 

- This is used for the extraction of the original signals on the reception side.

- A multiplexer or MUX is a device that is used for carrying out the multiplexing process and the demultiplexer or DEMUX is the device that performs demultiplexing. 

- IMUX or inverse multiplexing is another process whose aim is just the opposite of the multiplexing.

- It breaks down a single data stream in to various streams while transferring them at the same time over various communication channels.

- Later, the original stream is recreated.

Types of Multiplexing

Many different types of multiplexing technologies are available today. Each has its own significance:

Ø SDM or space-division multiplexing: 

This technique implies on using different point – to – point wires for individual communication channels. For example, an audio cable of analogue stereo, multi – pair telephone cable, switched star network, mesh network. However typically the wired SDM is not usually considered as multiplexing. In SDM a phased array antenna is formed by multiple antennas. For example MIMO (multiple – input and multiple – output), SIMO (simple – input and multiple – output), MISO (multiple – input and single – output) etc.

Ø  FDM or frequency-division multiplexing: 

This is considered to be an analog process, here the signals are sent in to different frequency ranges over a shared medium. For example, TV and radio broadcasting from satellite stations through the earth’s atmosphere. One cable is given in each house but over this cable many signals can be sent to other subscribers also. For accessing the desired signal, the users require to tune to that particular frequency. WDM or wavelength division multiplexing is a variant of FDM.

Ø TDM or time-division multiplexing: 

Unlike FDM, TDM is a digital technology but very rarely it might be used as an analog technology also. The process involves putting bytes in a sequence for each input stream one by one. this sequencing is done in such a way that the receiver can appropriately  receive them. If this is done quickly, the fact that another logical communication path was served in that circuit time won’t be detected by the receiver.

Ø  CDM or code-division multiplexing: 

In this multiplexing technique, the same frequency spectrum is shared by the several channels at the same time. Also the bandwidth of the spectrum is quite high when compared to the symbol rate or the bit rate. It is implemented in either of the two forms namely direct sequence spread spectrum and frequency hopping.

Some other types of multiplexing techniques which are less prominent are:

Polarization-division multiplexing: Used in optical and radio communications.

Orbital angular momentum multiplexing

What is meant by Quality of Service provided by network layer?

- The QoS or the quality of service is such a parameter that refers to a number of aspects of computer networks, telephony etc. 

- This parameter allows transportation of traffic as per some specific requirements. 

- Technology has advanced so much now computer networks can also be doubled up as the telephone networks for doing audio conversations. 

- The technology even supports the applications which have strict service demands. 

- The ITU defines the quality of service in telephony. 

It covers all the requirements concerning all the connection’s aspects such as the following:

Ø  Service response time

Ø  Loss

Ø  Signal – to – noise ratio

Ø  Cross – talk

Ø  Echo

Ø  Interrupts

Ø  Frequency response

Ø  Loudness levels etc.  

- The GoS (grade of service) requirement is one subset of the QoS and consists of those aspects of the connection that relate to its coverage as well as capacity. 

- For example, outage probability, maximum blocking probability and so on. 

- In the case of the packet switched telecommunication networks and computer networking, the resource reservation mechanisms come under the concept of traffic engineering. 

- QoS can be defined as the ability by virtue of which the different applications, data flows and users can be provided with different priorities. 

- It is important to have QoS guarantees if the capacity of the network is quite insufficient. 

- For example, voice over IP, IP-TV and so on. 

- All these services are sensitive to delays, have fixed bit rates and have limited capacities.

- The protocol or network supporting the QoS might agree up on some traffic contract with the network node’s reserve capacity and the software. 

- However, the quality of service is not supported by the best effort services. 

-Providing high quality communication over such networks provides a alternative to the QoS control mechanisms that are complex. 

- This happens when the capacity is over-provisioned so much that it becomes sufficient for the peak traffic load that has been expected. 

- Now since the network congestion problems have been eliminated, the QoS mechanisms are also not required. 

- It might be sometimes be taken as the level of the service’s quality i.e., the GoS. 

- For example, low bit error probability, low latency, and high bit rate and so on. 

- QoS can also be defined as a metric that reflects up on the experienced quality of the service.

- It is the cumulative effect that can be accepted. 

Certain types of the network traffic require a defined QoS such as the following:

Ø  Streaming media such as IPTV (internet protocol television), audio over Ethernet, audio over IP etc.

Ø  Voice over IP

Ø  Video conferencing

Ø  Telepresence

Ø  iSCSI, FCoE tec. Storage applications

Ø  safety critical applications

Ø  circuit emulation service

Ø  network operations support systems

Ø  industrial control systems

Ø  online games

- All the above mentioned services are examples of the inelastic services and a certain level of latency and bandwidth is required for them to operate properly. - On the other hand, the opposite kind of services such as the elastic services can work with any level of bandwidth and latency. 

- An example of these type of services is the bulk file transfer application based up on TCP.

- A number of factors affect the quality of service in the packet switched networks. 

- These factors can be broadly classified in to two categories namely technical and the human factors. 

The following factors are counted as the human factors:

Ø  reliability

Ø  scalability

Ø  effectiveness

Ø  maintainability

Ø  grade of service and so on.

- ATM (asynchronous transfer mode) or GSM like voice transmissions in the circuit switched networks have QoS in their core protocol. 

What are five key assumptions in dynamic channel allocation?

Putting the available bandwidth in operation of the cellular telephone system to efficient use is an important problem to be considered for providing good service to the largest number of customers possible. The problem has gained a critical status owing to the rapid growth of the cellular telephones users. 

- A communication channel is nothing but a band of frequencies which a number of users can use simultaneously if they are residing far apart from each other. 

- There is a minimum distance at which no interference occurs between the users and it is known as the channel reuse constraint. 

- A cellular telephone system divides the service area in to a number of regions commonly known as the cells. 

- Each of the cells has its own base station for handling the calls concerned with that cell. 

- The bandwidth of the communication channel is partitioned in to many channels permanently. 

- The cells are then allocated these channels in such a way that the channel reuse constraint is not violated by the calls. 

- There are a number of ways for allocating the channels. 

- Few of them are better than the others when it comes to reliably making channels available to all the cells. 

Few examples of channel allocation methods are:

1. Fixed assignment method
2. Dynamic allocation method
3. Reinforcement learning method

About Dynamic Method Allocation

- One type of dynamic method allocation is the BDCL or the borrowing with directional channel locking. 

- Out of all the above mentioned channel allocation methods, the dynamic allocation is considered the best one according to some studies conducted. 

- It is somewhat of the heuristic kind. 

- In dynamic allocation, the channels are allocated in the same way as in the fixed assignment method but it permits borrowing channels from the other cells whenever required. 

- It then arranges those channels in a specific order in each of the cells and this ordering is used in determining the channels for borrowing and reassigning the calls dynamically within the cells.

- There are static allocation techniques also but those don’t seem to work as well as the dynamic allocation techniques. 

In dynamic channel allocation 5 assumptions are always made which we have discussed below:

Station model: 

- There are N independent stations in the model and one frame is generated by each of the stations one at a time. 

- It is blocked until the successful transmission of the previous frame. 

- This means a station cannot queue multiple frames for transmission. 

- For example, a transmission gap of 100 bits is required during the transmission of the consecutive frames.

Single channel assumption:  

- The same medium is shared by all the stations. 

- Through it all the stations can receive and transmit.

Collision assumption: 

- A collision occurs whenever at the same time two frames are transmitted. 

- The two frames that collide have to be re-transmitted.

Transmission model: 

- There are 2 types namely, the continuous time model and the slotted time model. 

- In the former type transmission can be started at any given time. 

- In the latter model, transmission starts with a time slot.

Carrier sense: 

- It can also be classified in to 2 categories namely carrier sense and no carrier sense. 

- Stations can know if a channel is occupied prior to using it. This is called carrier sense.

- In no carrier sense, the stations cannot know whether the channel is occupied or not before transmission.

- Also, it gets difficult for the dynamic allocation method for setting up the favorable usage patterns as the calls start saturating the system. 

What is meant by Code Division Duplexing?

CDD or the Code Division Duplexing is a duplexing system that is perhaps the most spectrum – efficient one. In this article we discuss about this system. 

But first let us look at the scenario of the spectrum efficiency. 

- Elimination of interference is very complicated as well as an important issue when it comes to the implementation of the wireless communications. 

- With the increasing spectrum efficiency, interference becomes compulsory to be eliminated.

- Reducing the interference is very much important in order to increase the transmission data rate and the radio capacity of the wireless communications. 

- By duplexing, we mean that using two separate channels for the transmission of information in a two way communication in two different directions. 

- Currently we have only two working technologies in this regard namely:

1. Frequency division duplexing or FDD and
2. Time – division technology or TDD

- The former is the primary technology used in wireless because of its characteristic ability of interference isolation.

- The latter is kind of a spectral efficient technology.

- At present, frequency–division duplexing or FDD is mostly used by all the cellular systems for eliminating the interference that occurs in the adjacent cells. 

- A number of technologies are used today that have been successful in limiting the effects of the interference. 

- But they have not been successful in eliminating two particular types of interference namely:

1. Adjacent base – to – home mobile interference and
2. Adjacent mobile – to – home base interference

- Time Division Duplexing or TDD has not been put to use for the cellular systems since this one is much susceptible to different types of interference  

- TDD is not just subjected to the above mentioned two forms of interference rather it faces additional adjacent mobile to home and base to home interference.

- This limits the use of time division duplexing to the systems confined to a small area. 

- In Code–Division Duplexing, all these types of interference are eliminated making it the most spectrum efficient one. 

- However, proper CDD systems are not a perfect reality yet.

- CDD represents an innovative solution.

- Another best multiple access scheme is the CDMA (code – division multiple access) since it is more effective in eliminating the interference when compared to the other technologies. 

- Code – division duplexing is a combination of TDD and smart codes. 

- The CDD can be turned in to reality only with these smart codes. 

- CDMA based on these smart codes is termed as LAS – CDMA where LAS represents the smart codes set. 

- This technology holds the promise for increasing the spectral efficiency as well as capacity of the mobile networks. 

- For the efficient utilization of the spectrum, two technologies are required:

1. A multiple access scheme and
2. A duplexing system

- The industry has already established CDMA as the best out of three available (the other two are FDMA and TDMA). 

- Next, a duplexing system remains to be selected. 

- FDD has been the most common choice till now. 

- It makes use of different frequencies for handling the outgoing and incoming signals. 

- On the other hand, TDD operates on a single frequency but uses different time slots. 

- Using a TDD system provides a benefit of alternating sending and receiving in a single frequency. 

- Smart codes ensure that the code–division duplexing system is not like TDD but much better than that. 

- An interference limited environment was generated by the cellular systems using multiple frequencies in multiple cells. 

- Later, cells started using same frequency but still the environment was interference limited. 

- But the CDD system promises to change this environment in to one that is noise limited.